Poliasetal (POM) meme plakalarının orifis geometrisinde üretim kusurlarının eliptik fourier tanımlayıcılarıyla tespiti

Loading...
Thumbnail Image

Date

2016-06-13

Authors

Sayıncı, Bahadır

Journal Title

Journal ISSN

Volume Title

Publisher

Uludağ Üniversitesi

Abstract

Pestisit uygulamalarında yaygın olarak kullanılan termoplastik esaslı konik hüzmeli meme plakaları, belirli bir işletme basıncında kabul edilebilir sınırlarda debi sağlasa da orifis konturunda üretimden kaynaklanan şekil kusurları, püskürtme paterninin bozulmasına ve pülverizasyon kalitesinin düşmesine neden olmaktadır. Bu araştırma, nominal çapı 1.0, 1.2, 1.6, 2.0 ve 2.4 mm olan poliasetal (POM) malzemeden üretilmiş meme plakalarının orifis konturunda oluşan üretim kusurlarını eliptik Fourier tanımlayıcılarıyla tespit etmeyi amaçlamaktadır. Araştırmada, meme plakası görüntülerinde orifis şeklinin geometrisi kontur kodlarıyla tanımlanmış ve normalize edilerek kapalı orifis konturunun eliptik Fourier tanımlayıcıları elde edilmiştir. Bu tanımlayıcılar temel bileşenler analizine tabi tutulmuş ve elde edilen bileşen skorları kullanılarak saçılım grafikleri üzerinden üretim kusuru olan meme orifisleri tespit edilmiştir. Çok değişkenli varyans analizi (MANOVA) sonuçlarına göre meme orifisleri arasındaki kontur farklılıklarının çok önemli düzeyde farklı olduğu belirlenmiştir. Eşli karşılaştırma testi sonuçlarına göre 1.0 ve 1.2 mm çaplı meme plakalarının diğer meme gruplarına göre farklı olduğu belirlenmiştir. Kanonik ayırma skorları saçılım grafiğinde 1.6, 2.0 ve 2.4 mm çaplı orifislerin grup merkezleri birbirine yakın bulunmuştur. Deskriptif analiz sonuçlarına göre orifis konturları için belirlenen şekil parametrelerinin MANOVA sonuçlarıyla uyumlu olduğu saptanmıştır. Bu araştırmada, eliptik Fourier tanımlayıcıları kullanılarak anormal kontura sahip meme orifisleri başarılı bir şekilde tespit edilmiştir.
Even if the flow rates of hollow cone nozzle discs made in thermoplastic used widely in pesticide application were in the range of acceptable limits, the shape defection on orifice contour based on their manufacturing caused deteriorating the spray pattern and decreasing the spray quality. This study aimed detecting the manufacturing defects on the orifice contour of hollow cone pattern type nozzle disc, orifice diameters of which were 1.0, 1.2, 1.6, 2.0 and 2.4 millimeters, made in polyacetal (POM) material using elliptic Fourier descriptors. In the study, the geometry of the nozzle orifice was described using the codes of the closed-contour derived from the digitized orifice images, and generated elliptic Fourier descriptors of the closed contour using data normalized. These descriptors were subjected to the principal component analysis, and the defective nozzle orifices based on the manufacturing were detected from the scattered charts using the component scores of closed-contour of the orifices. According to the multivariate analysis (MANOVA), the contour differences between the nozzle orifices were statistically determined to be different. In accordance with the paired-comparison test, the contours of the nozzle orifices of 1.0 and 1.2 millimeters were found to be different than those of the other orifice groups. Canonical discriminant scores showed that the group centroids of the orifices of 1.6, 2.0 and 2.4 mm in diameter were found too close to each other. According to the results of the descriptive analysis, the shape parameters determined for the orifice contours were found compatible with MANOVA results. In this study, the nozzle orifices with abnormal contour were successfully detected using the elliptic Fourier descriptors.

Description

Keywords

Meme orifisi, Orifis konturu, Püskürtme paterni, Şekil analizi, Üretim hatası, Nozzle orifice, Orifice contour, Spray pattern, Shape analysis, Manufacturing error

Citation

Sayıncı, B. (2016). "Poliasetal (POM) meme plakalarının orifis geometrisinde üretim kusurlarının eliptik fourier tanımlayıcılarıyla tespiti". Uludağ Üniversitesi Ziraat Fakültesi Dergisi, 30(1), 57-73.